Ignition coils manufacturer and supplier with Hj-auto: How does an ignition coil work? The main task of the ignition coil is to transform the on-board voltage of 12V available in the vehicle to the required ignition voltage and then passed on to the spark plug. Basically, the function of the ignition coil is relatively simple to explain. The ignition coil itself contains a primary and a secondary winding. The primary winding has very few turns, while the secondary winding has very many. As soon as the engine control unit sends a signal to the ignition coil, the on-board voltage of 12V flows through the primary winding. Through this process, a magnetic field is built up. As soon as the signal from the engine control unit is interrupted again, this magnetic field is abruptly reduced. This abrupt degradation generates a high voltage in the secondary winding. This high voltage is now transmitted to the spark plug, which consequently generates a spark. See more information on https://www.hj-auto.com/ignition-coil.
Early cars came with one ignition coil. This coil pack was contained in a part called the distributor which was essentially a bundle of wires leading to each spark plug. The distributor was also responsible for timing each fuel ignition and could become de-calibrated over time, causing the engine to run out of sync. Around the 1980s, automakers began installing electronic sensors to handle ignition timing, and multiple ignition coils for better power and efficiency. Nowadays, most engines have an ignition coil placed directly on top of each spark plug. This is known as “coil on plug” configuration.
What is the reason? Here are some of them: The power supply voltage is unstable; The resistance of the high-voltage line is abnormal, replace the high-voltage line; There is a short circuit phenomenon in the secondary; The primary current of the ignition controller is too high, causing the ignition coil to overheat; Problems with high temperature and high-pressure wave work well; It is very unlikely that the coil itself is a problem, you can try another brand; The integrated block of the igniter does not work well. Total of 8 R&D personnel in our factory, Haiyan wholesale ignition coil suppliers have more than 15 years of working experience.
Using a collapsing magnetic field to induce an electric current: When a magnetic field has been created by applying an electric current to a coil of wire, any change in the electric current (increase or decrease in current flow) creates the same change in the magnetic field. If the electric current is switched off, the magnetic field will collapse. The collapsing magnetic field will then induce an electric current into the coil. If an electric current used to create a magnetic field is switched off, the magnetic field collapses, which induces another electric current into the coil.
The Kettering ignition system became virtually the only type of ignition system for mass-produced petrol cars, and stayed that way until electronically switched and controlled ignition systems started to replace mechanical ignition systems during the 1970s and 1980s. The basic principle of an ignition coil: To produce the required high voltages, ignition coils make use of the relationships that exist between electricity and magnetism. When an electric current flows through an electrical conductor such as a coil of wire, it creates a magnetic field around the coil (Figure 2). The magnetic field (or, more precisely, magnetic flux) is effectively a store of energy, which can then be converted back into electricity.
The products are produced by Haiyan hardware accessories manufacturer. It is highly resistant to temperature and heat. The manufactured hardware accessories have such merits of as to be used in the area. It is highly resistant to temperature and heat. Haiyan hardware accessories supplier has developed a broad market at home and abroad with its excellent quality, fast delivery, and timely and thoughtful service. It is highly resistant to temperature and heat. Read more info at hj-auto.com.
Haiyan car ignition coil suppliers have 200 workers, around 170 work over 4 years, with an independent long-term workflow and productivity, have one department including 30 products technology development and research. Our automotive ignition coil manufacturers cover over 14000 square meters, have been awarded city contracts and keeping promises to units, also we certify ISO9001, and TS16949 for a quality system, truly achieving the quality first, reputation first quality service for our customers at home and abroad. Kindly welcome domestic and overseas patrons to come and guide.
