The best paintless dent repair (PDR) in Colorado? In the first place let’s start with some car paint care tips: Applying dry ice to the dent is an effective way for fixing hail damage. The huge change in temperature can force the dents to pop out. Everything for you to do is just moving the dry ice around the damaged area to cool the area rapidly. But be careful as dry ice will damage your skin if you don’t wear gloves when handling it. Fixing hail damage by dry ice can be a cool solution, but sometimes it can not remove all of the dents. So in this case, you will need to do additional repairs.
Hailstorm damage is a car owner’s worst nightmare and can easily be avoided with a few cautionary steps: try to park your car in a shaded or covered area, especially during seasons when hailstorms are prevalent. If you’re going to be going out of town for an extended amount of time, make sure that your car is parked in an enclosed area and, if possible, have someone check on it once in a while. Open spaces will leave your car helpless against the wrath of this natural phenomenon.
Use Hot Glue, Wooden Dowels, & Screws: When you attempt to take out dents yourself, you always put the risk that you might further damage your car, whether you make the dent worse or chip the paint. A safe way of trying to take out big dents on your car is by using several wooden dowels, a few screws, and a hot glue gun. Simply place two nails into each side of the dowel and put the hot glue on the bottom. Place the dowels glue-side down in areas around the dent, repeat as many times as needed to cover the area, let them dry, and pull each one out until the dent is gone.
Don’t underestimate the necessary step of decontamination prior to application of your chosen wax. If you fail to do this step, you will get disappointing results regardless of the type of wax you have chosen. And yes…even that brand new car straight off the dealer lot will in have some form of pollutants already on the car paint from its travel from the factory to the car dealership. Clear coat is the top layer of your cars paint. It acts as a protective layer to filter out UV rays. But your clear coat is what you are trying to take care of with the above requirements. People get confused about clear coat vs. car paint. Virtually every car today is finished with a clear coat as the top layer. Think of it as car paint with no color added to it.
First, you have to pick a proper tool kit. And that’s not easy for a user who has little clue what’s going on. Some of them are cheap — low prices should raise red flags. Others are so expensive (three-figures or more) that they’re probably right up there with the cost of a decent professional repair (although, to be fair, if you buy the kit you can perform multiple repairs). Many of the high-end, expensive tools are intended to be used along the inside of the panel, much like a pro would do. (Gaining access to the inside of body panels can be a chore, though, and often involves careful removal of multiple interior trim pieces.) Alternatives (which tend to be the less expensive kits) flaunt the conventional wisdom that small dents should be massaged back out from behind the painted surface. These options instruct the user to glue a tool to the dented surface and then twist or pull on the tool to pop it out. True, you can go buy the same tools as a pro, but it takes a lot of skill and experience to use them properly. See extra details at Paint Protection Film Colorado Springs.
Paint Conditioner. If you’ve recently painted your vehicle or purchased a new vehicle, consider using a non abrasive paint conditioner to protect the paint. Non abrasive conditioners have to be sprayed on, in small amounts. Follow the instructions listed on the package to get good results. If you want to re-paint an old vehicle to maintain the exteriors, make sure you research the best new car paints available in the market. You need to also carefully follow car paint preparation techniques to do a good job.
The first step to performing a dent repair without using paint involves assessing the dent itself and determining if a paintless dent repair is even possible. According to most experts, 80 to 90 percent of dents can be repaired using PDR techniques. However, there are a certain percentage of dents that are impossible to repair without following it up with a paint job. The following types of dents usually fall into this “non-PDR” category: Very deep dents – Even very large dents can be repaired using PDR if the dent is fairly shallow. However, if a dent of any size is pushed in too far, the metal can’t be bent back into place without damaging the paint and requiring repainting.
